Aerospace Technic and Technology

The purpose of this work is to create a mathematical model of the stress state of overlapped circular axisymmetric adhesive joints and to build an appropriate analytical solution to the problem. To solve the problem, a simplified model of the adhesive bond of two overlapped plates is proposed. The simplification is that the movement of the layers depends only on the radial coordinate and does not depend on the angular one. The model is a generalization of the classical model of the connection of Holland and Reissner in the case of axial symmetry. The stresses are considered to be evenly distributed over the thickness of the layers, and the adhesive layer works only on the shift. These simplifications allowed us to obtain an analytical solution to the studied problem. The problem of the stress state of the adhesive bond of two plates is solved, one of which is weakened by a round hole, and the other is a round plate concentric with the hole. A load is applied to the plate weakened by a round hole. The discussed area is divided into three parts: the area of bonding, as well as areas inside and outside the bonding. In the field of bonding, the problem is reduced to third- and fourth-order differential equations concerning tangent and normal stresses, respectively, the solutions of which are constructed as linear combinations of Bessel functions of the first and second genera and modified Bessel functions of the first and second genera. Using the found tangential and normal stresses, we obtain linear inhomogeneous Euler differential equations concerning longitudinal and transverse displacements. The solution of the obtained equations is also constructed using Bessel functions. Outside the area of bonding, displacements are described by the equations of bending of round plates in the absence of shear forces. Boundary conditions are met exactly. The satisfaction of marginal conditions, as well as boundary conditions, leads to a system of linear equations concerning the unknown coefficients of the obtained solutions. The model problem is solved and the numerical results are compared with the results of calculations performed by using the finite element method. It is shown that the proposed model has sufficient accuracy for engineering problems and can be used to solve problems of the design of aerospace structures.

adhesive bonding; axisymmetric model; analytical solution; round plate

Savin, G. N. Raspredelenie napryazhenii okolo otverstii [Distribution of stresses around holes]. Kyiv, Naukova dumka Publ., 1968. 891 p.

Homa, I. Ju., Dashko, O. G. Napryazhennoe sostoyanie netonkoi transversal'no-izotropnoi plastiny s krivolineinym otverstiem [Stress State of Non-Thin Transversely Isotropic Plate with Curvilinear Hole]. Prikladnaja mehanika – International Applied Mechanics, 2015, vol. 51, iss. 4, pp. 112-124.

Guz, A. N. Establishing the Foundations of the Mechanics of Fracture of Materials Compressed Along Cracks (Review). International Applied Mechanics, 2014, vol. 50, pp. 1-57. DOI: 10.1007/s10778-014-0609-y.

Maksimjuk, V. A., Storozhuk, E. A., Chernyshenko, I. S. Napryazhenno-deformirovannoe sostoyanie gibkikh ortotropnykh tsilindricheskikh obolochek s podkreplennym krugovym otverstiem [Stress- Strain State of Flexible Orthotropic Cylindrical Shells with Stiffened Circular Hole]. Prikladnaja mehanika – International Applied Mechanics, 2015, vol. 51, iss. 4, pp. 71-80.

Zemlyanova, A. Y., Sil'vestrov, V. V. The problem of a circular patch. Journal of Applied Mathematics and Mechanics, 2005, vol. 69, iss. 4, pp. 611-617. DOI: 10.1016/j.jappmathmech.2005.07.010.

Khan, M.A., Kumar, S. Interfacial stresses in single-side composite patch-repairs with material tailored bondline. Mechanics of Advanced Materials and Structures, 2017, vol. 25, iss, 4, pp. 304-318. DOI: 10.1080/15376494.2016.1255824.

Okafor, A. C., Singh, N., Enemuoh, U. E., Rao, S. V. Design, analysis and performance of adhesively bonded composite patch repair of cracked aluminum aircraft panels. Composite Structures, 2005, vol. 71, iss. 2, pp. 258-270. DOI: 10.1016/j.compstruct.2005.02.023.

Zemlyanova, A. Y., Sil'vestrov V. V. The problem of the reinforcement of a plate with a cutout by a two-dimensional patch. Journal of Applied Mathematics and Mechanics, 2007, vol. 71, iss. 1, pp. 40-51.

Maksimenko, V. N., Tjagnij, A. V. Raschet napryazhennogo sostoyaniya kleeklepanykh sloistykh plastin s treshchinoi [Calculation of the stress state of glued laminated plates with a crack]. Uchenye zapiski TsAGI – TsAGI scientific notes, 1990, no. 5, pp. 92-101.

Kurennov, S. S., Polyakov, A. G., Barakhov, K. P. Two-Dimensional Stressed State of an Adhesive Joint. Nonclassical Problem. Journal of Mathematical Sciences, 2021, vol. 254, pp. 156-163. DOI: 10.1007/s10958-021-05295-5.

Zhang, Y., Zhang, K., Zhao, H., Xin, J., Duan, M. Stress analysis of adhesive in a cracked steel plate repaired with CFRP. Journal of Constructional Steel Research, 2018, vol. 145, pp. 210-217. DOI: 10.1016/j.jcsr.2018.02.029.

Kessentini, R., Klinkova, O., Tawfiq, I., Haddar, M. Transient hygro-thermo-mechanical stresses analysis in multi-layers bonded structure with coupled bidirectional model. International Journal of Mechanical Sciences, 2019, vol. 150, pp. 188-201. DOI: 10.1016/j.ijmecsci.2018.10.004.

Kurennov, S. S., Barakhov, K. P. Napryazhennoe sostoyanie dvukhsloinoi pryamougol'noi plastinki pri sdvige. Uproshchennaya dvumernaya model' [The Stressed state of the double-layer rectangular plate under shift. The simplified two-dimensional model]. Vestnik PNIPU. Mekhanika – PNRPU Mechanics Bulletin, 2019, no. 3, pp. 166-174. DOI: 10.15593/perm.mech/2019.3.16

Rapp, P. Mechanics of adhesive joints as a plane problem of the theory of elasticity. Part II: Displacement formulation for orthotropic adherends. Archives of Civil and Mechanical Engineering, 2015, vol. 15, iss. 2, pp. 603-619. DOI: 10.1016/j.acme.2014.06.004.

Kurennov, S. S. Determining Stresses in an Adhesive Joint with a Longitudinal Unadhered Region Using a Simplified Two-Dimensional Theory. Journal of Applied Mechanics and Technical Physics, 2019, vol. 60, pp. 740-747. DOI: 10.1134/s0021894419040199.

Barakhov, K., Dvoretskaya, D, Poliakov, O. One-Dimensional Axisymmetric Model of the Stress State of the Adhesive Joint. Intern. Sci. and Techn. Conf., Kharkiv, Ukraine; 29-30 Oct. 2020, pp. 310-319, (Lecture Notes in Networks and Systems Vol. 188). DOI: 10.1007/978-3-030-66717-7_26.

Grigorenko, A. Y., Los’, V. V., Malanchuk, V. A., Tormakhov, N. N. Stress State of a Threaded Joint in a Dental Implant-Bone System. International Applied Mechanics, 2020, vol. 56, pp. 33-39. DOI: 10.1007/s10778-020-00994-z.

da Silva, L. F. M., das Neves, P. J. C., Adams, R. D., Spelt, J. K. Analytical models of adhesively bonded joints. Part I: Literature survey. International Journal of Adhesion and Adhesives, 2009, vol. 29, iss. 3, pp. 319-330. DOI: 10.1016/j.ijadhadh.2008.06.005.